Welcome to x431creader.com! Sign In or Register
Home - LAUNCH News & Update Info - Update Information
« Go Back

BMW Diagnostic Software for X-431 Series V48.10

Compared with the previous version: 

updates as following: 

1. Added the functions of Read Version Information, Read DTCs, Clear DTCs, Read Data Streams, and Actuation Test for the MID (Multifunction display) and LRA (Headlight beam throw adjustment) systems under E39. 
2. Added the functions of Read Version Information, Read DTCs, Clear DTCs, Read Data Streams, and Actuation Test for the IHKA (Integrated Automatic Heating/ A/C Control) under F25. 
3. Added the functions of Read Version Information, Read DTCs, Clear DTCs, and Read Data Streams for the QMVH (Side moment distribution, rear axle) under F15. 
4. For the DME/DDE (Digital Motor Electronics/Digital Diesel Electronics) system under F01, F10, F20, and F30, added the following special functions: Evaluate sleep current monitoring、Check MSA system、OBD readiness code、Particulate filter replacement、Engine oil quantity、Preheating control unit、Zero gear sensor calibration、Clear adaptation values 
5. Added the following special functions for the EME (Motor electronic servo) under F01, F10, F20, and F30: DC/DC converter matching、Motor position sensor matching、High voltage battery charging 
6. Added the following special functions for the FEM/BDC/CAS (Car access system) under F01, F10, F20, and F30: Demonstration mode、Remote control start transmitter initialization setting、Electricity decrease command、Rain/running lamp/fog/sunlight sensor initialization setting、 Headlamp drive module initialization setting and LED demonstration、Reset starter lock、Block/enable、Personalization number、Rain/light sensor initialization setting、Window lifter drive device initialization setting 
7. Added the following for the SME (Memory management electronic device) under F01, F10, F20, and F30: High pressure safety check、Positioning isolation faulty 
8. Added the following for the DSC (Dynamic Stability Control) under F01, F10, F20, and F30: Bleeding program in special cases、Control unit matching、Brake pipe mixed check、Dynamic driving sensor matching 
9. Added the following for the EPS (Electric power steering system) under F01, F10, F20, and F30: EPS trial running 
10. Added the following for the LDM/ICMQL (Longitudinal dynamic management) under F01, F10, F20, and F30: Height matching 
11. Added the following for the ICMV (Integrated chassis control) under F01, F10, F20, and F30:Start trial running、Start self-diagnosis 
12. Added the following for the CIC/CHAMP (Head unit platform) under F01, F10, F20, and F30: Restore delivery status、Store MOST ring structure configuration 
13. Added the following for the FRM (Footwell module) under F01, F10, F20, and F30: Headlamp drive module initialization setting and LED demonstration 
14. Added the following for the IHKA (Integrated Automatic Heating/ A/C Control) under F01, F10, F20, and F30:Match low voltage limit、Execute flap motor correction running、Reposition flag motor、Unlocking、A/C compressor entry protection 
15. For the DME/DDE (Digital Motor Electronics/Digital Diesel Electronics) system under E60, E90, and E70, added the following:、OBD readiness code、Idle speed running quality、Operation stability measurement、Eccentric shaft adjustment、Zero gear sensor learning、Read AV system memory device、Check MSA system、Zero gear sensor learning/writing、Fuel supply limitation、Air flow sensor、Reset variant、Compression test、Stable running test、Wear test 
16. Added the following for the IHKA (Integrated Automatic Heating/ A/C Control) under E60, E90, and E70:Reposition flap motor、Electric steering column adjustment 
17. Added the following for the LDM (Longitudinal dynamic management) under E60, E90, and E70: Special measure reset coding data 
18. Added the following for the SGM-SIM/SRS (Safety and Information Module (SIM)) under E60, E90, and E70: Trigger roll bar、Read coding data 
19. Added the following for the CD (Control display) under E60, E90, and E70: Tuner,Japan、Restore delivery status 
20. Added the following for the CD-GW (Control display (gateway)/M-ASK-GW) under E60, E90, and E70:Store MOST ring structure configuration 
21. Added the following for the TCU (Telematic Control unit) under E60, E90, and E70:Restart BMW assist、Deregister CKPH 
22. Added the following for the NAV (Navigation system) under E60, E90, and E70:DVD lockup
23. Added the following for the NVK (Night view camera) under E60, E90, and E70: Vertical adjustment 
24. Added the following for the DSC (Dynamic Stability Control) under E46: Read in vehicle identification no.(ABS/ASC) 
25. Added the following for the ABS (Anti-lock Brake System) system under E39, E38, and E53: Control unit replacement 
26. For the DME/DDE (Digital Motor Electronics/Digital Diesel Electronics) system under E39, E38, E46, and E53, added the following:CO adjustment、Clear adaptation values、Stable running measurement、Idle speed adjustment、EGR、Fuel supply limitation、Start fuel supply、OBD readiness code、VANOS test、Mix learning values、Compare specified/actual values、Engine speed record、Safety Test、Start quantity、Full load limiting delivery、Exhaust Gas Recirculation,Air Mass、Additive rate adjustment、Start of injection map、Exhaust Gas Recirculation Map、Reset engine control unit pairing(PMS)、Reset maximum engine coolant temperature reached 
27. For the DME/DDE (Digital Motor Electronics/Digital Diesel Electronics) system under E60, E90, and E70, optimized the following:Eccentric shaft adjustment、Tolerance test, Middle position control lever、Check MSA system、Oil consumption indicator lamp adjustment 
28. For the DME/DDE (Digital Motor Electronics/Digital Diesel Electronics) system under E39, optimized the following:DME (DDE) -EWS (CAS) adjustment 
         
Support products: 

        X-431 3G II,X-431 GDS I, X-431 3G III, X-431 GDS II,X-431 IV, X-431 Diagun III, X-431 Pad, X-431 Matco PAD,X-431 Pro,X-431 V,X-431 V+,EasyDiag,ScanPad071,ScanPad101,X431 PadII, X431 PRO3, MaxGo, Maximus 2.0, CRP229,golo技师